644 lines
27 KiB
C++
644 lines
27 KiB
C++
#include "uds_handler.h"
|
|
#include "connections/canconmanager.h"
|
|
#include "mainwindow.h"
|
|
#include "isotp_handler.h"
|
|
#include <QDebug>
|
|
|
|
static QVector<CODE_STRUCT> UDS_DIAG_CTRL_SUB = {
|
|
{1,"DFLT_SESS", "Default session"},
|
|
{2,"PROG_SESS", "Programming Session"},
|
|
{3,"EXT_SESS", "Extended Diagnostics Session"},
|
|
{4,"SAFETY_SESS", "Safety System Diagnostics Session"},
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_ECU_RESET_SUB = {
|
|
{1,"HARD_RESET", "Hard reset of ECU"},
|
|
{2,"KEYOFFON_RESET", "Simulated key off then on reset"},
|
|
{3,"SOFT_RESET", "Soft reset - leaving RAM intact"},
|
|
{4,"EN_POWERDOWN_RESET", "Enable sleep mode"},
|
|
{5,"DIS_POWERDOWN_RESET", "Disable sleep mode"},
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_COMM_CTRL_SUB = {
|
|
{0,"COMM_NORMAL", "Enable both Rx and Tx of normal messages"},
|
|
{1,"COMM_DIS_TX", "Enable reception of normal messages but don't Tx them"},
|
|
{3,"COMM_DIS_ALL", "Disable both Rx and Tx of non-diagnostics messages"},
|
|
{4,"COMM_DIS_TX_ENH", "Addressed bus master should turn off TX on related sub-bus"},
|
|
{5,"COMM_ENHANC", "Addressed bus master should set related sub-bus to app scheduling mode"},
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_ROUTINE_SUB = {
|
|
{1,"START_ROUTINE", "Start routine by given ID"},
|
|
{2,"STOP_ROUTINE", "Stop routine by given ID"},
|
|
{3,"GET_ROUTINE_RESULTS", "Get results from routine specified by ID"},
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_FILE_MODEOFOP = {
|
|
{1, "ADDFILE", "Add file to file system"},
|
|
{2, "DELETEFILE", "Add file to file system"},
|
|
{3, "REPLACEFILE", "Add file to file system"},
|
|
{4, "READFILE", "Add file to file system"},
|
|
{5, "READDIR", "Add file to file system"}
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_SERVICE_DESC = {
|
|
{1, "OBDII_SHOW_CURRENT", "OBDII - Show current data"},
|
|
{2, "OBDII_SHOW_FREEZE", "OBDII - Show freeze data"},
|
|
{3, "OBDII_SHOW_STORED_DTC", "OBDII - Show stored DTC codes"},
|
|
{4, "OBDII_CLEAR_DTC", "OBDII - Clear current DTC codes"},
|
|
{5, "OBDII_TEST_O2", "OBDII - O2 sensor testing"},
|
|
{6, "OBDII_TEST_RESULTS", "OBDII - Show emissions testing results"},
|
|
{7, "OBDII_SHOW_PENDING_DTC", "OBDII - Show pending DTC codes"},
|
|
{8, "OBDII_CONTROL_DEVICES", "OBDII - Control vehicle devices"},
|
|
{9, "OBDII_VEH_INFO", "OBDII - Retrieve vehicle information"},
|
|
{0xA, "OBDII_PERM_DTC", "OBDII - Show permanent DTC codes"},
|
|
{0x10, "DIAG_CONTROL", "Diagnostic session control"},
|
|
{0x11, "ECU_RESET", "Reset ECU"},
|
|
{0x12, "GMLAN_READ_FAILURE_RECORD", "GMLAN - Read Fail"},
|
|
{0x14, "CLEAR_DIAG", "Clear diagnostic trouble codes"},
|
|
{0x19, "READ_DTC", "Read diagnostic trouble codes"},
|
|
{0x1A, "GMLAN_READ_DIAGNOSTIC_ID", "GMLAN - Read diagnostics ID"},
|
|
{0x20, "RETURN_TO_NORMAL", "Return to normal mode"},
|
|
{0x21, "READ_BY_LOCALID", "Read data by Local ID"},
|
|
{0x22, "READ_BY_ID", "Read data by ID"},
|
|
{0x23, "READ_BY_ADDR", "Read data by address"},
|
|
{0x24, "READ_SCALING_ID", "Read scaling data by ID"},
|
|
{0x27, "SECURITY_ACCESS", "Request security access"},
|
|
{0x28, "COMM_CTRL", "Communication control"},
|
|
{0x2A, "READ_DATA_ID_PERIODIC", "Read data by ID periodically"},
|
|
{0x2C, "DYNAMIC_DATA_DEFINE", "Create dynamic data ID"},
|
|
{0x2D, "DEFINE_PID_BY_ADDR", "Create a PID for a given memory address"},
|
|
{0x2E, "WRITE_BY_ID", "Write data by ID"},
|
|
{0x2F, "IO_CTRL", "Input/Output control (force)"},
|
|
{0x31, "ROUTINE_CTRL", "Call a service routine"},
|
|
{0x34, "REQUEST_DOWNLOAD", "Request data download (from PC to ECU)"},
|
|
{0x35, "REQUEST_UPLOAD", "Request data upload (from ECU to PC)"},
|
|
{0x36, "TRANSFER_DATA", "Transfer data"},
|
|
{0x37, "REQ_TRANS_EXIT", "Request that data transfer cease"},
|
|
{0x38, "REQ_FILE_TRANS", "Request file transfer"},
|
|
{0x3B, "GMLAN_WRITE_DID", "GMLAN - Write DID"},
|
|
{0x3D, "WRITE_BY_ADDR", "Write data by address"},
|
|
{0x3E, "TESTER_PRESENT", "Tester is present"},
|
|
{0x7F, "NEG_RESPONSE","Negative Response"},
|
|
{0x83, "ACCESS_TIMING", "Read or write comm timing parameters"},
|
|
{0x84, "SECURED_DATA_TRANS", "Secured data transmission"},
|
|
{0x85, "CTRL_DTC_SETTINGS", "Control DTC settings"},
|
|
{0x86, "RESPONSE_ON_EVENT", "Request start/stop transmission on event"},
|
|
{0x87, "RESPONSE_LINK_CTRL", "Control comm link"},
|
|
{0xA2, "GMLAN_REPORT_PROG_STATE", "GMLAN - Report programming state"},
|
|
{0xA5, "GMLAN_ENTER_PROG_MODE", "GMLAN - Enter programming mode"},
|
|
{0xA9, "GMLAN_CHECK_CODES", "GMLAN - Check codes"},
|
|
{0xAA, "GMLAN_READ_DPID", "GMLAN - Read dynamic PID"},
|
|
{0xAE, "GMLAN_DEVICE_CTRL", "GMLAN - Device control"},
|
|
{0xFF, "UNKNOWN_CODE", "Unknown, likely proprietary UDS function code"}
|
|
};
|
|
|
|
static QVector<CODE_STRUCT> UDS_NEG_RESPONSE =
|
|
{
|
|
{0x10, "GENERAL_REJECT", "General rejection (no other codes matched)"},
|
|
{0x11, "SERVICE_NOTSUPP", "ECU does not support this service code"},
|
|
{0x12, "SUBFUNCT_NOTSUPP", "ECU does not support the requested sub function"},
|
|
{0x13, "INVALID_FORMAT", "Invalid request length or format error"},
|
|
{0x14, "RESPONSE_TOOLONG", "Response would be too long to send"},
|
|
{0x21, "BUSY", "ECU is busy. Try again later"},
|
|
{0x22, "COND_INCORR", "A prereq. condition was not met"},
|
|
{0x24, "REQ_SEQ_ERR", "Invalid sequence of requests"},
|
|
{0x25, "SUBNET_NORESP", "ECU tried to gateway request but response timed out"},
|
|
{0x26, "FAILURE", "A failure (indicated in a DTC) is preventing a reply"},
|
|
{0x31, "REQ_OUTOFRANGE", "A parameter is outside of the valid range"},
|
|
{0x33, "SECURITY_DENIED", "Security access was denied. (invalid seq or ECU not unlocked?)"},
|
|
{0x35, "INVALID_KEY", "Key passed was invalid. Failure counter has been incremented."},
|
|
{0x36, "EXCEED_ATTEMPTS", "Key failed too many times. ECU security access locked out"},
|
|
{0x37, "TIMEDELAY", "Security access too soon after last attempt"},
|
|
{0x38, "EXT_SECUR_1", "Extended security failure code 1"},
|
|
{0x39, "EXT_SECUR_2", "Extended security failure code 2"},
|
|
{0x3A, "EXT_SECUR_3", "Extended security failure code 3"},
|
|
{0x3B, "EXT_SECUR_4", "Extended security failure code 4"},
|
|
{0x3C, "EXT_SECUR_5", "Extended security failure code 5"},
|
|
{0x3D, "EXT_SECUR_6", "Extended security failure code 6"},
|
|
{0x3E, "EXT_SECUR_7", "Extended security failure code 7"},
|
|
{0x3F, "EXT_SECUR_8", "Extended security failure code 8"},
|
|
{0x40, "EXT_SECUR_9", "Extended security failure code 9"},
|
|
{0x41, "EXT_SECUR_10", "Extended security failure code 10"},
|
|
{0x42, "EXT_SECUR_11", "Extended security failure code 11"},
|
|
{0x43, "EXT_SECUR_12", "Extended security failure code 12"},
|
|
{0x44, "EXT_SECUR_13", "Extended security failure code 13"},
|
|
{0x45, "EXT_SECUR_14", "Extended security failure code 14"},
|
|
{0x46, "EXT_SECUR_15", "Extended security failure code 15"},
|
|
{0x47, "EXT_SECUR_16", "Extended security failure code 16"},
|
|
{0x48, "EXT_SECUR_17", "Extended security failure code 17"},
|
|
{0x49, "EXT_SECUR_18", "Extended security failure code 18"},
|
|
{0x4A, "EXT_SECUR_19", "Extended security failure code 19"},
|
|
{0x4B, "EXT_SECUR_20", "Extended security failure code 20"},
|
|
{0x4C, "EXT_SECUR_21", "Extended security failure code 21"},
|
|
{0x4D, "EXT_SECUR_22", "Extended security failure code 22"},
|
|
{0x4E, "EXT_SECUR_23", "Extended security failure code 23"},
|
|
{0x4F, "EXT_SECUR_24", "Extended security failure code 24"},
|
|
{0x70, "UPLOAD_DOWNLOAD", "Fault when attempting to start upload/download"},
|
|
{0x71, "TRX_SUSPENDED", "Transfer aborting due to a fault"},
|
|
{0x72, "GEN_PROGRAMMING", "Fault while attempting to write to ECU memory"},
|
|
{0x73, "WRONG_BLOCK_SEQ", "Invalid sequence value detected during transfer"},
|
|
{0x78, "RESP_PENDING", "Request successful but ECU still busy - Response pending"},
|
|
{0x7E, "SUBFUNCT_CURRSESS", "ECU does not support this subfunction in current session type"},
|
|
{0x7F, "SERVICE_CURRSESS", "ECU does not support this service in current session type"},
|
|
{0x81, "RPM_TOOHIGH", "RPM is too high to execute request"},
|
|
{0x82, "RPM_TOOLOW", "RPM is too low to execute request"},
|
|
{0x83, "ENGINE_RUNNING", "Cannot execute request while engine is running"},
|
|
{0x84, "ENGINE_NOTRUNNING", "Cannot execute request while engine is off"},
|
|
{0x85, "ENG_RUNTIME_LOW", "Cannot execute request until engine has run for longer"},
|
|
{0x86, "TEMPERATURE_HIGH", "Cannot execute request until temperature is lower"},
|
|
{0x87, "TEMPERATURE_LOW", "Cannot execute request until temperature is higher"},
|
|
{0x88, "SPEED_HIGH", "Cannot execute request until vehicle slows down"},
|
|
{0x89, "SPEED_LOW", "Cannot execute request until vehicle is going faster"},
|
|
{0x8A, "PEDAL_HIGH", "Cannot execute request until throttle is lower"},
|
|
{0x8B, "PEDAL_LOW", "Cannot execute request until throttle is higher"},
|
|
{0x8C, "NOT_NEUTRAL", "Cannot execute request until transmission is in neutral"},
|
|
{0x8D, "NOT_INGEAR", "Cannot execute request until vehicle is in gear"},
|
|
{0x8F, "BRAKE_NOTPRESSED", "Cannot execute request until brake pedal is pressed (Hold down)"},
|
|
{0x90, "NOT_PARK", "Cannot execute request until vehicle is in park"},
|
|
{0x91, "CLUTCH_LOCKED", "Cannot execute request while clutch is locked"},
|
|
{0x92, "VOLTAGE_HIGH", "Cannot execute request until voltage is lower"},
|
|
{0x93, "VOLTAGE_LOW", "Cannot execute request until voltage is higher"},
|
|
};
|
|
|
|
UDS_MESSAGE::UDS_MESSAGE()
|
|
{
|
|
subFunc = 0;
|
|
service = 0;
|
|
subFuncLen = 1;
|
|
isErrorReply = false;
|
|
}
|
|
|
|
UDS_HANDLER::UDS_HANDLER()
|
|
{
|
|
isReceiving = false;
|
|
useExtendedAddressing = false;
|
|
modelFrames = MainWindow::getReference()->getCANFrameModel()->getListReference();
|
|
isoHandler = new ISOTP_HANDLER();
|
|
}
|
|
|
|
UDS_HANDLER::~UDS_HANDLER()
|
|
{
|
|
delete isoHandler;
|
|
}
|
|
|
|
UDS_MESSAGE UDS_HANDLER::tryISOtoUDS(ISOTP_MESSAGE msg, bool *result)
|
|
{
|
|
const unsigned char *data = reinterpret_cast<const unsigned char *>(msg.payload().constData());
|
|
int dataLen = msg.payload().count();
|
|
*result = true;
|
|
UDS_MESSAGE udsMsg;
|
|
udsMsg.bus = msg.bus;
|
|
udsMsg.setExtendedFrameFormat(msg.hasExtendedFrameFormat());
|
|
udsMsg.setFrameId(msg.frameId());
|
|
udsMsg.isReceived = msg.isReceived;
|
|
udsMsg.setTimeStamp(msg.timeStamp());
|
|
udsMsg.reportedLength = msg.reportedLength;
|
|
udsMsg.service = 0;
|
|
udsMsg.subFunc = 0;
|
|
udsMsg.subFuncLen = 0;
|
|
udsMsg.isErrorReply = false;
|
|
udsMsg.setPayload(msg.payload());
|
|
if (dataLen > 0) {
|
|
udsMsg.service = data[0];
|
|
if (udsMsg.service == 0x7F)
|
|
{
|
|
udsMsg.isErrorReply = true;
|
|
if (dataLen > 1)
|
|
{
|
|
udsMsg.service = data[1];
|
|
if (dataLen > 2) udsMsg.subFunc = data[2];
|
|
else
|
|
{
|
|
*result = false;
|
|
return udsMsg;
|
|
};
|
|
}
|
|
else
|
|
{
|
|
*result = false;
|
|
return udsMsg;
|
|
};
|
|
udsMsg.payload().remove(0, 2);
|
|
}
|
|
else
|
|
{
|
|
udsMsg.isErrorReply = false;
|
|
if (dataLen > 1) udsMsg.subFunc = data[1];
|
|
udsMsg.payload().remove(0, 1);
|
|
}
|
|
}
|
|
else
|
|
{
|
|
*result = false;
|
|
};
|
|
return udsMsg;
|
|
}
|
|
|
|
void UDS_HANDLER::gotISOTPFrame(ISOTP_MESSAGE msg)
|
|
{
|
|
qDebug() << "UDS handler got ISOTP frame";
|
|
UDS_MESSAGE udsMsg;
|
|
|
|
bool result;
|
|
udsMsg = tryISOtoUDS(msg, &result);
|
|
|
|
if (result) emit newUDSMessage(udsMsg);
|
|
}
|
|
|
|
void UDS_HANDLER::setFlowCtrl(bool state)
|
|
{
|
|
isoHandler->setFlowCtrl(state);
|
|
}
|
|
|
|
void UDS_HANDLER::setReception(bool mode)
|
|
{
|
|
if (isReceiving == mode) return;
|
|
|
|
isReceiving = mode;
|
|
|
|
if (isReceiving)
|
|
{
|
|
connect(isoHandler, SIGNAL(newISOMessage(ISOTP_MESSAGE)), this, SLOT(gotISOTPFrame(ISOTP_MESSAGE)));
|
|
isoHandler->setReception(true); //must enable ISOTP reception too.
|
|
qDebug() << "Enabling reception of ISO-TP frames in UDS handler";
|
|
}
|
|
else
|
|
{
|
|
disconnect(isoHandler, SIGNAL(newISOMessage(ISOTP_MESSAGE)), this, SLOT(gotISOTPFrame(ISOTP_MESSAGE)));
|
|
isoHandler->setReception(false);
|
|
qDebug() << "Disabling reception of ISOTP frames in UDS handler";
|
|
}
|
|
}
|
|
|
|
void UDS_HANDLER::sendUDSFrame(const UDS_MESSAGE &msg)
|
|
{
|
|
QByteArray data;
|
|
if (msg.bus < 0) return;
|
|
if (msg.bus >= CANConManager::getInstance()->getNumBuses()) return;
|
|
if (msg.service > 0xFF) return;
|
|
|
|
data.append(msg.service);
|
|
for (int b = msg.subFuncLen - 1; b >= 0; b--)
|
|
{
|
|
data.append((msg.subFunc >> (8 * b)) & 0xFF);
|
|
}
|
|
|
|
data.append(msg.payload());
|
|
isoHandler->sendISOTPFrame(msg.bus, msg.frameId(), data);
|
|
|
|
//qDebug() << "Data sending: " << data;
|
|
|
|
qDebug() << "Sent UDS service: " << getServiceShortDesc(msg.service) << " on bus " << msg.bus;
|
|
}
|
|
|
|
QString UDS_HANDLER::getShortDesc(QVector<CODE_STRUCT> &codeVector, int code)
|
|
{
|
|
foreach (CODE_STRUCT codeRec, codeVector)
|
|
{
|
|
if (codeRec.code == code) return codeRec.shortDesc;
|
|
}
|
|
return QString();
|
|
}
|
|
|
|
QString UDS_HANDLER::getLongDesc(QVector<CODE_STRUCT> &codeVector, int code)
|
|
{
|
|
foreach (CODE_STRUCT codeRec, codeVector)
|
|
{
|
|
if (codeRec.code == code) return codeRec.longDesc;
|
|
}
|
|
return QString();
|
|
}
|
|
|
|
QString UDS_HANDLER::getServiceShortDesc(int service)
|
|
{
|
|
QString ret;
|
|
ret = getShortDesc(UDS_SERVICE_DESC, service);
|
|
if (ret.length() == 0)
|
|
ret = getShortDesc(UDS_SERVICE_DESC, service + 0x40);
|
|
return ret;
|
|
}
|
|
|
|
QString UDS_HANDLER::getServiceLongDesc(int service)
|
|
{
|
|
QString ret;
|
|
ret = getLongDesc(UDS_SERVICE_DESC, service);
|
|
if (ret.length() == 0)
|
|
ret = getLongDesc(UDS_SERVICE_DESC, service + 0x40);
|
|
return ret;
|
|
}
|
|
|
|
QString UDS_HANDLER::getNegativeResponseShort(int respCode)
|
|
{
|
|
QString ret;
|
|
ret = getShortDesc(UDS_NEG_RESPONSE, respCode);
|
|
return ret;
|
|
}
|
|
|
|
QString UDS_HANDLER::getNegativeResponseLong(int respCode)
|
|
{
|
|
QString ret;
|
|
ret = getLongDesc(UDS_NEG_RESPONSE, respCode);
|
|
return ret;
|
|
}
|
|
|
|
/*
|
|
* This function kind of breaks the hands off approach of the rest of the class. In here
|
|
* we dig deep into nitty gritty details of UDS and much more of this is hardcoded
|
|
* to the UDS standard than the rest of the code where the code doesn't really know anything
|
|
* about what it is doing - it just reads arrays and such.
|
|
* No, in here we end up with hard coded handlers to figure out each type of message and how to
|
|
* interpret it to a fine level of detail. Look away code purists, this is likely to be a mess.
|
|
* The output here is potentially multi-line and is useful for debugging a UDS problem. You'll
|
|
* get a finely detailed dump of exactly what the message means.
|
|
*/
|
|
QString UDS_HANDLER::getDetailedMessageAnalysis(const UDS_MESSAGE &msg)
|
|
{
|
|
QString buildString;
|
|
int dataSize;
|
|
int addrSize;
|
|
int compType, encType;
|
|
const unsigned char *data = reinterpret_cast<const unsigned char *>(msg.payload().constData());
|
|
int dataLen = msg.payload().length();
|
|
|
|
if (msg.isErrorReply)
|
|
{
|
|
buildString.append("UDS ERROR Response\n");
|
|
buildString.append("Service: " + getServiceLongDesc(msg.service) + "\n");
|
|
}
|
|
else if (msg.service < 0x3F || (msg.service > 0x7F && msg.service < 0xAF)) {
|
|
buildString.append("UDS Request\n");
|
|
buildString.append("Service: " + getServiceLongDesc(msg.service) + "\n");
|
|
}
|
|
else
|
|
{
|
|
buildString.append("UDS Positive Response\n");
|
|
buildString.append("Service: " + getServiceLongDesc(msg.service - 0x40) + "\n");
|
|
}
|
|
|
|
if (msg.isErrorReply)
|
|
{
|
|
//Negative responses replace the sub function with an error code instead
|
|
buildString.append("Negative response: " + getLongDesc(UDS_NEG_RESPONSE, msg.subFunc) + "\n");
|
|
}
|
|
else
|
|
{
|
|
switch (msg.service)
|
|
{
|
|
case UDS_SERVICES::DIAG_CONTROL:
|
|
//diag control requests have one parameter - which type of session we want.
|
|
buildString.append("Session Request: " + getLongDesc(UDS_DIAG_CTRL_SUB, msg.subFunc));
|
|
break;
|
|
case UDS_SERVICES::DIAG_CONTROL + 0x40: //positive response
|
|
buildString.append("Session Request: " + getLongDesc(UDS_DIAG_CTRL_SUB, msg.subFunc));
|
|
//there should be four extra bytes now
|
|
if (dataLen < 5) //5 because subfunc codes are left in data so it starts with one subfunc byte
|
|
{
|
|
//buildString.append("\nReturned data payload wasn't at least \n4 bytes like it should have been");
|
|
}
|
|
else
|
|
{
|
|
int p2 = data[1] * 256 + data[2];
|
|
buildString.append("\nP2MAX (Max Wait / Resp Time): " + QString::number(p2) + "ms");
|
|
p2 = (data[3] * 256 + data[4]) * 10;
|
|
buildString.append("\nP2 Ext MAX: " + QString::number(p2) + "ms");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::ECU_RESET:
|
|
//ECU reset has one parameter - which reset type to ask for
|
|
buildString.append("Reset Type: " + getLongDesc(UDS_ECU_RESET_SUB, msg.subFunc));
|
|
break;
|
|
case UDS_SERVICES::ECU_RESET + 0x40:
|
|
buildString.append("Reset Type: " + getLongDesc(UDS_ECU_RESET_SUB, msg.subFunc));
|
|
//There should be one additional byte which encodes power down time
|
|
if (dataLen > 1)
|
|
{
|
|
if (data[1] < 0xFF)
|
|
{
|
|
buildString.append("\nMinimum powered down time: " + QString::number(data[1]));
|
|
}
|
|
else buildString.append("\nPowerdown time not available");
|
|
}
|
|
else buildString.append("\nNo powerdown time returned");
|
|
break;
|
|
case UDS_SERVICES::COMM_CTRL:
|
|
//Comm control has potentially a lot of parameters. control type, comm type, nodeID
|
|
buildString.append("Control type: " + getLongDesc(UDS_COMM_CTRL_SUB, msg.subFunc));
|
|
if (dataLen > 1)
|
|
buildString.append("\nComm Type: " + QString::number(data[1])); //TODO: no attempt to interpret yet
|
|
if (dataLen > 3)
|
|
{
|
|
int nodeID = (data[2] * 256 + data[3]);
|
|
buildString.append("\nNode ID: " + Utility::formatHexNum(nodeID));
|
|
}
|
|
break;
|
|
case UDS_SERVICES::SECURITY_ACCESS:
|
|
if ((msg.subFunc % 2) == 1)
|
|
{
|
|
buildString.append("Seed request for security level: " + QString::number(msg.subFunc) + "\n");
|
|
if (dataLen > 1)
|
|
{
|
|
buildString.append("Data payload: ");
|
|
for (int j = 2; j < dataLen; j++) buildString.append(Utility::formatHexNum(data[j]) + " ");
|
|
}
|
|
}
|
|
else
|
|
{
|
|
buildString.append("Key sending for security level: " + QString::number(msg.subFunc - 1));
|
|
if (dataLen > 1) //and it sure as hell should be!
|
|
{
|
|
buildString.append(" KEY: ");
|
|
for (int j = 2; j < dataLen; j++) buildString.append(Utility::formatHexNum(data[j]) + " ");
|
|
}
|
|
}
|
|
break;
|
|
case UDS_SERVICES::SECURITY_ACCESS + 0x40:
|
|
if ((msg.subFunc % 2) == 1)
|
|
{
|
|
buildString.append("Seed response for security level: " + QString::number(msg.subFunc) + "\n");
|
|
if (dataLen > 1) //be kinda pointless if it weren't
|
|
{
|
|
buildString.append("SEED: ");
|
|
for (int j = 2; j < dataLen; j++) buildString.append(Utility::formatHexNum(data[j]) + " ");
|
|
}
|
|
}
|
|
else
|
|
{
|
|
buildString.append("Positive response to key for security level: " + QString::number(msg.subFunc - 1));
|
|
buildString.append("\nECU is now unlocked");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::READ_BY_ID:
|
|
//parameter is groups of two bytes, each of which specify an ID to read
|
|
if (dataLen > 2)
|
|
{
|
|
uint32_t id;
|
|
for (int i = 1; i < dataLen; i = i + 2)
|
|
{
|
|
id = (data[i] * 256) + data[i+1];
|
|
buildString.append("\nID to read: " + Utility::formatHexNum(id));
|
|
}
|
|
}
|
|
break;
|
|
case UDS_SERVICES::READ_BY_ID + 0x40: //reply
|
|
buildString.append("Reply is non-standard and so no decoding is done. The format is (ID) followed by how ever much data that ID returns, followed by more ID/data pairs if applicable.\nPayload: ");
|
|
for (int i = 1; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::READ_BY_ADDR:
|
|
//subfunc byte specifies address and length format, then address, then size
|
|
dataSize = msg.subFunc >> 4;
|
|
addrSize = msg.subFunc & 0xF;
|
|
if (dataLen > (dataSize + addrSize))
|
|
{
|
|
buildString.append("Address: 0x");
|
|
for (int i = 0; i < addrSize; i++) buildString.append(QString::number(data[1+i], 16).toUpper().rightJustified(2,'0'));
|
|
buildString.append("\nSize: 0x");
|
|
for (int i = 0; i < dataSize; i++) buildString.append(QString::number(data[1+i+addrSize], 16).toUpper().rightJustified(2,'0'));
|
|
}
|
|
else
|
|
{
|
|
buildString.append("Message has insufficient bytes to properly decode address and size!");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::READ_BY_ADDR + 0x40:
|
|
buildString.append("Reply is a raw packet of data of the size requested.\nPayload: ");
|
|
for (int i = 1; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::WRITE_BY_ID:
|
|
if (dataLen > 3)
|
|
{
|
|
int writeID = (data[1] * 256 + data[2]);
|
|
buildString.append("ID to write to: " + Utility::formatHexNum(writeID) + "\nPayload: ");
|
|
for (int i = 3; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
}
|
|
break;
|
|
case UDS_SERVICES::WRITE_BY_ID + 0x40:
|
|
if (dataLen > 2)
|
|
{
|
|
int writeID = (data[1] * 256 + data[2]);
|
|
buildString.append("ID written to: " + Utility::formatHexNum(writeID));
|
|
}
|
|
break;
|
|
case UDS_SERVICES::ROUTINE_CTRL:
|
|
buildString.append("Routine Control: " + getLongDesc(UDS_ROUTINE_SUB, msg.subFunc));
|
|
if (dataLen > 3)
|
|
{
|
|
int routineID;
|
|
routineID = (data[2] * 256 + data[3]);
|
|
buildString.append("\nRoutine ID: " + Utility::formatHexNum(routineID));
|
|
}
|
|
if (dataLen > 4)
|
|
{
|
|
buildString.append("\nParameter bytes to routine: ");
|
|
for (int i = 4; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
}
|
|
break;
|
|
case UDS_SERVICES::ROUTINE_CTRL + 0x40:
|
|
buildString.append("Routine Control: " + getLongDesc(UDS_ROUTINE_SUB, msg.subFunc));
|
|
if (dataLen > 2)
|
|
{
|
|
int routineID;
|
|
routineID = (data[2] * 256 + data[3]);
|
|
buildString.append("\nRoutine ID: " + Utility::formatHexNum(routineID));
|
|
}
|
|
if (dataLen > 4)
|
|
{
|
|
buildString.append("\nBytes returned by routine: ");
|
|
for (int i = 4; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
}
|
|
break;
|
|
case UDS_SERVICES::REQUEST_DOWNLOAD:
|
|
case UDS_SERVICES::REQUEST_UPLOAD:
|
|
compType = data[1] >> 4;
|
|
encType = data[1] & 0xF;
|
|
buildString.append("Compression Type: " + QString::number(compType));
|
|
if (compType == 0) buildString.append(" (none)");
|
|
buildString.append("\n");
|
|
buildString.append("Encryption Type: " + QString::number(encType));
|
|
if (encType == 0) buildString.append(" (none)");
|
|
buildString.append("\n");
|
|
//subfunc byte specifies address and length format, then address, then size
|
|
dataSize = data[2] >> 4;
|
|
addrSize = data[2] & 0xF;
|
|
if (dataLen > (dataSize + addrSize))
|
|
{
|
|
buildString.append("Address: 0x");
|
|
for (int i = 0; i < addrSize; i++) buildString.append(QString::number(data[3 + i], 16).toUpper().rightJustified(2,'0'));
|
|
buildString.append("\nSize: 0x");
|
|
for (int i = 0; i < dataSize; i++) buildString.append(QString::number(data[3 + i + addrSize], 16).toUpper().rightJustified(2,'0'));
|
|
}
|
|
else
|
|
{
|
|
buildString.append("Message has insufficient bytes to properly decode address and size!");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::REQUEST_DOWNLOAD + 0x40:
|
|
case UDS_SERVICES::REQUEST_UPLOAD + 0x40:
|
|
dataSize = data[1] >> 4;
|
|
buildString.append("\nMax Size of data block: 0x");
|
|
for (int i = 0; i < dataSize; i++) buildString.append(QString::number(data[2 + i], 16).toUpper().rightJustified(2,'0'));
|
|
break;
|
|
case UDS_SERVICES::TRANSFER_DATA:
|
|
case UDS_SERVICES::TRANSFER_DATA + 0x40:
|
|
buildString.append("\nBlock Sequence: " + QString::number(data[1], 16) + "\nPayload: ");
|
|
for (int i = 2; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::REQ_TRANS_EXIT:
|
|
case UDS_SERVICES::REQ_TRANS_EXIT + 0x40:
|
|
buildString.append("\nPayload: ");
|
|
for (int i = 1; i < dataLen; i++)
|
|
{
|
|
buildString.append(Utility::formatHexNum(data[i]) + " ");
|
|
}
|
|
break;
|
|
case UDS_SERVICES::REQ_FILE_TRANS:
|
|
break;
|
|
case UDS_SERVICES::WRITE_BY_ADDR:
|
|
break;
|
|
}
|
|
}
|
|
|
|
//qDebug() << buildString;
|
|
return buildString;
|
|
}
|
|
|
|
//Little shim functions that drop straight through to the ISO_TP handler
|
|
void UDS_HANDLER::setProcessAllIDs(bool state)
|
|
{
|
|
isoHandler->setProcessAll(state);
|
|
}
|
|
|
|
void UDS_HANDLER::addFilter(uint32_t pBusId, uint32_t ID, uint32_t mask)
|
|
{
|
|
isoHandler->addFilter(pBusId, ID, mask);
|
|
}
|
|
|
|
void UDS_HANDLER::removeFilter(uint32_t pBusId, uint32_t ID, uint32_t mask)
|
|
{
|
|
isoHandler->removeFilter(pBusId, ID, mask);
|
|
}
|
|
|
|
void UDS_HANDLER::clearAllFilters()
|
|
{
|
|
isoHandler->clearAllFilters();
|
|
}
|
|
|